Micropolis 4221WAV

Hard Disk Drive

Overview

Model	Capacity	Size	Height	Interface	Bus Type
Micropolis 4221WAV	2050MB	3 1/2"			SCSI2

Specifications

Size	3 1/2"
Interface	SCSI-2
Encoding Method
Formatted Capacity	2,050 MB
Disks	5
Heads	9
Cylinders	4150
Sectors	Variable
Buffer Size	N/A
Average Seek	8.9. msec
Single Track
Rotation Speed/Avg. Latency	7200 rpm +/- 0.5%
Transfer Rate to / from. media	20 Mbytes/sec Synchronous
Transfer Rate to / from buffer
Tracks Per Inch (TPI)
Bits Per Inch (BPI)
Dimensions	5.75"D x 4.0"W x 1.0"H
Weight	0.00 lbs.

Power Requirements

	+12V +/-5%	+5V +/-5%	Power
Spin up	.5A
Read / Write	1.7A	.9A
Typical seeking			11.5 Watts

Notes

Configuration and Jumper Options

SCSI ID Selection
Up to sixteen devices (the host and fifteen targets) can be attached to the SCSI bus.
These are selected with jumpers on the Option Jumper Block or on Auxiliary
Connector J1B (use either but not both); see the Note below the J1B drawing for J1B usage.
In multiple-device systems, each device must have its own Unique SCSI ID.
The SCSI ID (drive address) jumpers are identified as ID0, ID1, ID2, and ID3.
ID selection is binary, as shown below.

SCSI ID	ID3	ID2	ID1	ID0
0 (Default)	out	out	out	out
1	out	out	out	in
2	out	out	in	out
3	out	out	in	in
4	out	in	out	out
5	out	in	out	in
6	out	in	in	out
7	out	in	in	in
8	in	out	out	out
9	in	out	out	in
10	in	out	in	out
11	in	out	in	in
12	in	in	out	out
13	in	in	out	in
14	in	in	in	out
15	in	in	in	in

Interface Termination
If terminators are installed at RN1, RN2, and RN3 (default), the drive provides termination for the SCSI interface. If the terminators are not installed, the drive does not provide interface termination. SCSI terminators are installed only in the end devices on the SCSI cable; remove the terminators from each of the other devices. The SCSI Host Adapter card and the last drive in the chain should have terminators.

Terminator Power
W1 and W2 select the source of power (+5V) for the interface terminators; W3 controls the drive supplying +5V to the bus.

W1	W2	W3
Y	N	-	Drive provides terminator power. (Default)
N	Y	-	Host provides terminator pwr via J1 pin 26 to RN1 and RN2
-	-	Y	Drive supplies +5V to the bus via J1 pin 26. (Default)

Remote LED
A user-supplied LED may be connected to Remote LED (Pins 1 and 2).

Spindle Options Jumpers at SP0 (Pins 11 and 12) and SP1 (Pins 13 and 14) control the spindle options. SP0 SP1 N N The drive starts the spindle motor at power-on. (Default) Y N The drive waits for a Start Unit SCSI command to start the spindle motor. N Y Spindle start-up is delayed based on SCSI ID address (12 seconds per ID)

Write Protect A jumper at WP (Pins 15 and 16) selects the write protect option. Jumper The drive is write protected. No Jumper The drive is not write protected. (Default)
Parity A jumper at PTY (Pins 17 and 18) selects the bus parity check option. The drive always generates parity regardless of this option. Jumper SCSI interface parity checking disabled. No Jumper SCSI interface parity checking on. (Default)

Spindle Sync Signals Use of the MSYNC and SSYNC signals is optional. These signals are used as spindle synchronization reference.

Auxiliary Connector J1B

Note:
J1B is sampled at initialization for jumpers on pins 7-8, 5-6, 3-4, and 1-2 for SCSI ID3, ID2, ID1, and ID0 respectively; these connections (if not jumpered) are then released for the following usages: A dash character (-) at the end of a signal name indicates that it is asserted at the low level (i.e., active low) and negated at the high level.

Drive Fault (XTFALT-) Output signal negated (Default); indicates no drive fault. Output signal asserted; indicates a drive fault condition.

Slave Sync (SSYNC-) Use is optional; used as spindle synchronization reference.
Remote LED- Open collector output; used to drive a user-supplied LED to indicate the drive is active.
Ground (GND) Logic ground; provides signal ground.
+5 Volts (+5V) 5 VDC (1A max); used to drive external LEDs.
Write Protect (FAULT-) Input signal negated (Default); drive is not write protected. Input signal asserted; drive is write protected.